Yocto in action!
https://www.dropbox.com/s/b4nlongb6xo7w ... III-21.jpg
Search found 11 matches
- Apr 15th, '14, 08:19
- Forum: Yocto v1.0 Hardware
- Topic: Exploring other enclosure options.
- Replies: 433
- Views: 400675
- Mar 14th, '14, 07:16
- Forum: Yocto v1.0 Hardware
- Topic: Exploring other enclosure options.
- Replies: 433
- Views: 400675
Re: Exploring other enclosure options.
i did dis 1: https://www.dropbox.com/s/5oisg343ye31plc/DSCF2692.JPG Did you use acryl for the front and output plates? No acryl, I used 2mm steel plates for the front, output and base. all sides are oak wood. 2mm for plates is too much, 1mm is enough. is going to be too heavy. The next time I would...
- Mar 11th, '14, 21:11
- Forum: Yocto v1.0 Hardware
- Topic: Exploring other enclosure options.
- Replies: 433
- Views: 400675
- Feb 10th, '14, 21:57
- Forum: Yocto v1.0 Hardware
- Topic: Cymbal R108* and R111* wrong value
- Replies: 6
- Views: 7146
Re: Cymbal R108* and R111* wrong value
my yocto's cymbal works fine. if I change R108 to 22K and R111 to 18K, then what happens otherwise, whether sound or what happen if i do not change?
- Feb 10th, '14, 21:43
- Forum: Yocto v1.0 Hardware
- Topic: Hand Clap Sound problem
- Replies: 42
- Views: 69711
Re: Hand Clap Sound problem
Everything works, even a HandClap. All resistors were correct but I soldered resistors around BA6110 all over again, and it worked. 
- Feb 10th, '14, 11:56
- Forum: Yocto v1.0 Hardware
- Topic: Noise section trimmer voltage?
- Replies: 81
- Views: 65703
Re: Noise section trimmer voltage?
I also changed R127 value 4.7K to 47K to get 130mV. Why is R127 value 4.7 K in the tutorial and why I had to change in order to get the correct value?
- Feb 5th, '14, 21:37
- Forum: Yocto v1.0 Hardware
- Topic: Hand Clap Sound problem
- Replies: 42
- Views: 69711
Re: Hand Clap Sound problem
Thanks, it's a good opportunity without SCOP. Before I take scope I checked to measure the noise and was not able to get a 130mV tuning the trimmer. only 3.6mV (i don't know what does it mean). after checking resistors in noise area i found that the resistors R130 is not 1M (only 54K). Is it possibl...
- Feb 5th, '14, 15:12
- Forum: Yocto v1.0 Hardware
- Topic: Hand Clap Sound problem
- Replies: 42
- Views: 69711
Re: Hand Clap Sound problem
no, I don't have scope I need to borrow a friend. Here you can listen to how the sounds TM3 full left is it same like you had? http://soundcloud.com/out-or/yocto-handclap-problem/s-jhVAr one case was heard as the clap but this change quickly. At first I suspected that the cold soldered. I found no s...
- Feb 5th, '14, 09:17
- Forum: Yocto v1.0 Hardware
- Topic: Hand Clap Sound problem
- Replies: 42
- Views: 69711
Re: Hand Clap Sound problem
Thank you!
how much it affects handclap 's sound. I tried a handclap for a trimmer and a variety of placements but the sound is not gone 808 characteristic's handclap sound.
how much it affects handclap 's sound. I tried a handclap for a trimmer and a variety of placements but the sound is not gone 808 characteristic's handclap sound.
- Feb 5th, '14, 08:51
- Forum: Yocto v1.0 Hardware
- Topic: Hand Clap Sound problem
- Replies: 42
- Views: 69711
Re: Hand Clap Sound problem
All other functions are working well but the problem is the CB and HC. I put some pictures here: https://www.dropbox.com/sh/6jr5u9q7oniz2eh/4sQTEE64W-
If the CB does'nt have a trimmer how to calibrate?
If the CB does'nt have a trimmer how to calibrate?