e-licktronic Forum

Dear Diyer,

Here is the Nava v1.0 Mouser BOM and the complete PDF part list
If you want to save money you can order basic part by Tayda then order specific part by Mouser. Have a look on this topic

To complete your kit you need 26x 11mm Orange d-shaft knob, 1x 21mm black knob and 1x 21mm orange knob. A 15VAC 1000mA psu and a case available on this topic

EDIT 09/14/20
Bom Updated

EDIT 09/04/19
-BFC237086333 Vishay capacitor replace by Nichicon
-20K ohm RN55C2002BB14 Vishay resistor replace by Yageo
-1N5819 StMicroelectronic Diode rectifier replace by Rectron
-56nF Panasonic ECQ-E2563JB capacitor replace by Kemet
-100pF FK28C0G1H101J TDK capacitor replace by Vishay
Bom Updated

EDIT 11/19/18
-MFR-25FRF52-1K8 replace by Xicon
-KCDX-5S-N replace by KCDX-5S-N2
-UVZ1HR33MDD replace by 0.33uF 63V Wurth Electronics
- RGA4R7M1HBK-0511G replace by 475CKR100M
-HCF4051YM013TR replace by NLHV4051DR2G
Nava BOM updated with no backorder components

EDIT 07/16/18
-MC7815CTG replace by SCD7815CTG
- 23PS139 styroflex caps still out of stock
-S471K29X7RP63K5R replace by S471K25Y5PN6TJ5R
-CFR16J4K7 replace by CFR-25JT-52-4K7
-K104K15X7RF53H5 replace by RDEF51H104Z0M1H03A
-TL074CDT replace by TL074IYDT
-885012207072 replace by 08051C104J4T4A
-BOM updated

EDIT 02/15/18
All components are in stock
-BOM updated

EDIT 11/2/17
-MFR-25FRF52-47K replace by MFR-25FTE52-47K
-390pF Styroflex capacitor still out of stock (can be find by Musikding
)
-BOM updated


EDIT 10/20/17
-Parts needed for the Mux/Sh boards added
-TL074 IC110 replace by a TL072 IC1
-390pF Styroflex capacitor still out of stock (can be find by Musikding
)
-BOM updated

EDIT 04/12/17
-330R Yageo resistor replace by CFR-25JR-52-330R
-2700pF Kemet capacitors replace by MMK5272J63J01L16.5TA18
-47pF Xicon capacitors replace by Vishay K470K15C0GH53L2
-0.047uF Nichicon capacitor replace by QYX1H473JTP
-Abracon 16MHz crystal replace by FOXSLF/160-20
BOM Complete


EDIT 03/10/17
-0.047uF and 0.01uF capacitor quantity updated
-22K Yageo resistor replace by KOA Speer
-100R Yageo resistor replace by new reference
-390pF styroflex capacitor still out of stock but you can find it by Musikding

EDIT 03/02/17
-Mouser BOM updated
-Rubber feet out of stock
-390pF styroflex capacitor still out of stock but you can find it by Musikding

EDIT 02/14/17
-56nF Kemet film capacitor replace by Panasonic

EDIT 02/10/17
-1M5 resistor replace reference
-Vishay 0ohm resistors replace by Yageo
-Vishay 100pf 100VDC ceramic capacitor replace by TDK 50VDC
-Vishay 10K trimmer replace by Bourns
-1nF nichicon QYX2 capacitor replace by QYX1
-47nF nichicon QYX2 10% capacitor replace by 5%
-390pF styroflex capacitor out of stock until April. You can find this capacitor by Musikding

EDIT 01/29/17
-Molex 22-01-3067 6 pin housing connector replace by Molex 10-11-2063 (compatible with 7879 series crimp)

EDIT 01/17/17
-Bourns PTV112-4420-B503 potentiometer deleted to the BOM if you received the wrong master potentiometer have a look here

EDIT 01/9/17
-0.1uF 100V capacitors deleted (already present in the BOM)

EDIT 12/27/16
-Bourns PTV112-4420-B503 potentiometer added to the BOM
-10kOhm Yageo Resistors replace by the New Yageo reference
-0.68uF Panasonic capacitor replace by Nichicon
-2N3906 Fairchild replace by MCC

EDIT 12/09/16
-Nava Mouser Bom updated

EDIT 9/13/16
-10K vishay multiturn trimmer replace by Bourns 3296W
-Bourns Encoder non detent replace by 24 detent
-Kemet 0.047uF capacitor replace by Nichicon
-2200uF 35V Nichicon capacitor replace by Kemet
-39Kohm Xicon resistor replace by Koa Speer metal film
--Red backlight 16x2 LCD Still OUT OF STOCK (can find on Ebay)

EDIT 8/15/16
-1K2 resistor replace by KOA speer
-Red backlight 16x2 LCD Still OUT OF STOCK (can find on Ebay)
-390pF Polystyren capacitor Still OUT OF STOCK (available by Musikding or BanzaiMusic)

EDIT 8/15/16
-Nava Mouser BOM updated
-Red backlight 16x2 LCD OUT OF STOCK (can find on Ebay)
-390pF Polystyren capacitor OUTOF STOCK (available by Musikding or BanzaiMusic)


EDIT 6/8/16
-MF1/4LCT52R105J Koa Speer 1M resistor replace by MF1/4LCT52R105G

EDIT 5/23/16
-Add Kemet R82EC3100AA70J 0.1uF capacitor 7pcs
-1Kohm resistor quantity updated to 29pcs
-1K2ohm resistor quantity updated to 41pcs
-20Kohm resistor quantity updated to 5pcs
-FCI 68000-416HLF 16 pins male pin header added to the BOM

EDIT 5/21/16
-20Kohm resistor quantity updated to 5 pcs
-68Kohm resistor quantity updated to 4 pcs
-100kohm CFR-25JR-52-100K Yageo resistors replace by 291-100K-RC Xicon

EDIT 5/20/16
-100pF capacitor quantity updated to 5 pcs

EDIT 5/18/16
Important update! On semiconductor EEprom does not seems to work with current firmware so you need the Microchip one
-On semiconductor CAT24M01 EEprom replace by Microchip 24LC1025

EDIT 5/17/16
-Nichicon 0.027uF cap QYX1H273KTP replace by Panasonic ECQ-E2273KF3

EDIT 5/3/16
Nava v1.0 Mouser Bom updated

Best regards,
e-licktronic

Hi
The 32 electrolytes (10uF) in the pdf are listed as 16v, but in the Mouser they are 50v. I guess the 50v will be fine?
Thanks for a nice kit!

50V is fine, lead spacing and package size is the same.

Thanks!
And all the carbon-film resistors in the BOM. Is that for old-shool authenticity?
GOt my kit and will start now

Kit arrived today so I was about to order the BOM, however this part is no longer in print?
"End of Life: Scheduled for obsolescence and will be discontinued by the manufacturer."
http://www.mouser.com/ProductDetail/Nic ... 50tw%3d%3d

Mouser #: 647-QYX1H273KTP
Mfr. #: QYX1H273KTP
Manufacturer: Nichicon
Desc.: Film Capacitors 50volts 0.027uF

Can you suggest a replacement part on Mouser so I can complete my parts list please?

DrRek wrote:Kit arrived today so I was about to order the BOM, however this part is no longer in print?
"End of Life: Scheduled for obsolescence and will be discontinued by the manufacturer."
http://www.mouser.com/ProductDetail/Nic ... 50tw%3d%3d

Mouser #: 647-QYX1H273KTP
Mfr. #: QYX1H273KTP
Manufacturer: Nichicon
Desc.: Film Capacitors 50volts 0.027uF

Can you suggest a replacement part on Mouser so I can complete my parts list please?

Please check the lead spacing on the PCB, is it 3.5mm or 5mm?
I think it is 3.5mm so the replacement part has 5mm, you´ll need to bend it like this: \ /
Replacement part:
Mouser Part #: 647-QYX2A273KTP
Manufacturer Part #: QYX2A273KTP

Hurry, as of now only 32 pcs. left...

LED holder/spacer is to big, the Build guide spacer differ in color and size.

I found some infos that the CD4040BE can't be used in the 909/nava, correct is cd4040UB.
Maybe that's the reason for some issues in crash, ride, hats

The white LED mounts won't fit. To wide for placing them side by side :-/

The IC sockets will not mount to the surface because of the middle "bridge".
(Solved this problem by cutting the "bridge" out)

drifter7508 wrote:The white LED mounts won't fit. To wide for placing them side by side :-/

The IC sockets will not mount to the surface because of the middle "bridge".
(Solved this problem by cutting the "bridge" out)

The LED mounts can be easily cut with a sharp household knife to fit better.