Secondary Noise Source Kit

Discuss mods, hacks, tweaks, etc.

Re: Secondary Noise Source Kit

Postby Peter » Jul 13th, '16, 13:48

I also got noise kit and knobs today, thank you!
Peter
 
Posts: 10
Joined: Apr 26th, '16, 20:19

Re: Secondary Noise Source Kit

Postby Jojjelito » Jul 13th, '16, 19:51

Mine arrived in the Stockholm region today as well. Thank you!
Jojjelito
 
Posts: 20
Joined: Jan 8th, '15, 01:33
Location: Stockholm

Re: Secondary Noise Source Kit

Postby Patrick » Jul 24th, '16, 23:02

The second noise source works great, i drilled a further hole in the pcb and mount it with a 16mm spacer on the middle nava pcb hole which hold happymums case too.
User avatar
Patrick
 
Posts: 62
Joined: Jan 6th, '14, 19:16
Location: Germany

Re: Secondary Noise Source Kit

Postby Rowan » Jul 25th, '16, 21:24

I got my noise PCB today, I haven't assemble it yet.

I was also thinking that the best way to mount it would be drill a hole in the centre and use a male>female threaded spacer to fix in to one of the stand-offs that was the PCB attaches to.

Where did you take the +15V from on the main board? I haven't thought about this as of yet.

Edit: I just remembered there is a header that's labelled for for an optional CV/Gate board that have +15V and GND on it...... That will be the place to get power from.
Rowan
 
Posts: 38
Joined: Jun 22nd, '15, 12:34

Re: Secondary Noise Source Kit

Postby AonFluX » Jul 28th, '16, 12:36

Im starting to assemble the board, but it looks a little wierd on the print.
The bigger footprint below the 33k resistor looks like a film resistor, but has the value of 100 pF printed, and besides the electrolyte, it looks like a ceramic cap footprint, but with the value 100nF. Have the values been mistacenly swapped?

And then noice out from the board can be connected to the listed leg of R208 in the handclap section, right?
AonFluX
 
Posts: 68
Joined: Apr 27th, '16, 07:26

Re: Secondary Noise Source Kit

Postby Altitude » Jul 28th, '16, 14:32

Just like this, ceramic throughout. 2.5mm LS is the most common for 100n, I put 5mm in for the 100p so you can use axial ones as well:

Image

You pull out one side of R208 and solder to that.
User avatar
Altitude
 
Posts: 147
Joined: May 28th, '15, 13:01

Re: Secondary Noise Source Kit

Postby AonFluX » Jul 28th, '16, 20:05

Thanks for the clarification! :)
AonFluX
 
Posts: 68
Joined: Apr 27th, '16, 07:26

Re: Secondary Noise Source Kit

Postby Grizzlydj » Aug 9th, '16, 12:43

I want one. Order closed? :roll:
Grizzlydj
 
Posts: 53
Joined: Jun 11th, '16, 22:44

Re: Secondary Noise Source Kit

Postby Altitude » Aug 9th, '16, 15:02

Yes. These are sold out
User avatar
Altitude
 
Posts: 147
Joined: May 28th, '15, 13:01

Re: Secondary Noise Source Kit

Postby Grizzlydj » Aug 9th, '16, 18:32

email me if will be a second chance
Grizzlydj
 
Posts: 53
Joined: Jun 11th, '16, 22:44

PreviousNext

Return to Nava Mods

Who is online

Users browsing this forum: No registered users and 1 guest