Page 6 of 8

Re: Extra9 - NAVA Expansion Kits

PostPosted: Jun 12th, '19, 21:38
by secrethero303
poser1 wrote:It's great to hear that people are receiving their cases! I was wondering if anybody in the states has had one arrive yet? Thanks...

Mine arrived last week!

Re: Extra9 - NAVA Expansion Kits

PostPosted: Jun 16th, '19, 16:59
by kmosch
hy, i have problems with BD attack and noise, and SD snappy since i've installed the extra 9 pcb. They do nothing, without pcb the function was ok. have anyone the same problem? Greetings.

Re: Extra9 - NAVA Expansion Kits

PostPosted: Jun 16th, '19, 18:18
by KlangGenerator
kmosch wrote:hy, i have problems with BD attack and noise, and SD snappy since i've installed the extra 9 pcb. They do nothing, without pcb the function was ok. have anyone the same problem? Greetings.


I'd say IC33 died. To find out, remove IC33 and place it's companion (IC32) inside the socket.

Re: Extra9 - NAVA Expansion Kits

PostPosted: Jun 19th, '19, 01:47
by Macgyverradio
Haven't gotten mine yet. But I'm in California might take a little longer.

Re: Extra9 - NAVA Expansion Kits

PostPosted: Jun 24th, '19, 14:33
by kmosch
KlangGenerator wrote:
kmosch wrote:hy, i have problems with BD attack and noise, and SD snappy since i've installed the extra 9 pcb. They do nothing, without pcb the function was ok. have anyone the same problem? Greetings.


I'd say IC33 died. To find out, remove IC33 and place it's companion (IC32) inside the socket.



so i get 2 new mitsubishi 4006er, both was died. so SD and Handclap is ok, BD Attack and Noise do not. On R10 i have the Signat from the 4006, but how looks the signal at the test point for noise? the same?

Re: Extra9 - NAVA Expansion Kits

PostPosted: Jul 5th, '19, 23:52
by mmoody
Are any kits still available (no case)?

Re: Extra9 - NAVA Expansion Kits

PostPosted: Jul 7th, '19, 00:32
by poser1
My case from Kacper finally arrived yesterday! Looks good so far but I haven't checked yet to see if everything lines up correctly with the PCB...

Re: Extra9 - NAVA Expansion Kits

PostPosted: Jul 13th, '19, 19:27
by e-licktronic
poser1 wrote:My case from Kacper finally arrived yesterday! Looks good so far but I haven't checked yet to see if everything lines up correctly with the PCB...



Lucky guy i'm still waiting for mine :(
Can you share picture of yours ?

Re: Extra9 - NAVA Expansion Kits

PostPosted: Jul 20th, '19, 03:10
by poser1
Sure, I took some photos but can't figure out how to post them... shall I just PM them to you?

Re: Extra9 - NAVA Expansion Kits

PostPosted: Jul 23rd, '19, 02:13
by secrethero303
kmosch wrote:hy, i have problems with BD attack and noise, and SD snappy since i've installed the extra 9 pcb. They do nothing, without pcb the function was ok. have anyone the same problem? Greetings.


I had the same issue with mine after the Extra9 upgrade. Turns out the problem was with my ability to clearly read the instructions. I had all of the wires going to the attack pot and didn’t see that the 2nd wore is actually supposed to go to the pcb. Once I fixed that everything worked 100%. Hopefully your issue is something simple too.