Page 4 of 4

Re: Yoctov1.0 Firmware Update.

Posted: Nov 7th, '16, 10:11
by hofmann25
SO I've tried updating firmware. v1.0c.

I get the all steps blink twice then when I press play on SysEx librarian the steps on the Yocto don't light up as the firmware plays out of SysEx. TX Speed is at 25%.

Is this normal?

Re: Yoctov1.0 Firmware Update.

Posted: Dec 30th, '16, 07:13
by richardlawson1489
Thanks for the update. Keep us updated with Yocto updates.

Re: Yoctov1.0 Firmware Update.

Posted: Jul 7th, '17, 16:52
by morelius21
Hi

If i programming the amtega whit avrstudio i need to change any fuse in the burn proces?

thanks

Re: Yoctov1.0 Firmware Update.

Posted: Jul 12th, '17, 18:24
by antto
if you have a new atmega, or an atmega that has been used for running something different (different project) then you'd need to use a programmer device, configure the fuse and lock bits, program the bootloader, and then, using the bootloader you can put the actual firmware

if this is an already working chip, then you must already have the fuse bits, lock bits, and bootloader programmed and working

Re: Yoctov1.0 Firmware Update.

Posted: Jul 14th, '17, 11:25
by agalops87
Hi,

I'm about to update my Yocto. I have the original 2.0 software. I'll use Sysex Librarian at 25% speed ( it seems to be the good configuration for mac if I refer to forum posts )
Do I have to install the updates one by one ( 1.0a then 1.0b ... ) or can I install the 1.0c ?
Thanks for support.

Re: Yoctov1.0 Firmware Update.

Posted: Jun 13th, '19, 18:31
by rv0
agalops87 wrote:Hi,

I'm about to update my Yocto. I have the original 2.0 software. I'll use Sysex Librarian at 25% speed ( it seems to be the good configuration for mac if I refer to forum posts )
Do I have to install the updates one by one ( 1.0a then 1.0b ... ) or can I install the 1.0c ?
Thanks for support.
I know, old post, but as nobody replied to you, and this is a pinned thread about the firmware and people might not find the other thread for unofficial firmware:

- No need to install multiple updates, I would recommend to just take the latest unofficial firmware from https://github.com/HomoElectromagneticu ... 8/releases (currently: 1.2b) and install that.
- I always use Elektron C6 as it works really well and the default settings are perfect. But SysExLibrarian works just as good with the right settings.

Re: Yoctov1.0 Firmware Update.

Posted: Jul 1st, '19, 14:58
by mmoody
any fix to the double trigger yet?

Re: Yoctov1.0 Firmware Update.

Posted: Nov 7th, '19, 11:58
by toosmoothchrist
hofmann25 wrote:SO I've tried updating firmware. v1.0c.

I get the all steps blink twice then when I press play on SysEx librarian the steps on the Yocto don't light up as the firmware plays out of SysEx. TX Speed is at 25%.

Is this normal?
A friend of mine just bought a Yocto with a big bug on the master section + an impossibility to upgrade the firmware.. same behaviour as the one you describe... Did you ever find a solution?

thanks

Re: Yoctov1.0 Firmware Update.

Posted: Nov 28th, '19, 19:24
by helectromagneticus
toosmoothchrist wrote:
hofmann25 wrote:SO I've tried updating firmware. v1.0c.

I get the all steps blink twice then when I press play on SysEx librarian the steps on the Yocto don't light up as the firmware plays out of SysEx. TX Speed is at 25%.

Is this normal?
A friend of mine just bought a Yocto with a big bug on the master section + an impossibility to upgrade the firmware.. same behaviour as the one you describe... Did you ever find a solution?

thanks
The Yocto is very picky about firmware updates. You need to set a delay of 200ms between SysEx messages for the update to work, and the messages must start within five seconds of the lights blinking.In SysEx Librarian, the delay setting is called "Pause between played messages" and not transmit speed.