Page 1 of 1
I goofed. Please help
Posted: Feb 9th, '17, 17:21
by onebase
Hello, I managed to plug a 12V dc plug into my yocto for a short period of time and it no longer turns on. I hope the issue is isolated to the psu.
Any suggestions on how to start a fix if possible would be greatly appreciated.
BEST
~
J
Re: I goofed. Please help
Posted: Feb 9th, '17, 18:23
by e-licktronic
onebase wrote:Hello, I managed to plug a 12V dc plug into my yocto for a short period of time and it no longer turns on. I hope the issue is isolated to the psu.
Any suggestions on how to start a fix if possible would be greatly appreciated.
BEST
~
J
Onebase,
First check PSU voltage +15v, -15v and +5V
Best regards,
e-licktronic
Re: I goofed. Please help
Posted: Feb 9th, '17, 19:01
by onebase
e-licktronic wrote:onebase wrote:Hello, I managed to plug a 12V dc plug into my yocto for a short period of time and it no longer turns on. I hope the issue is isolated to the psu.
Any suggestions on how to start a fix if possible would be greatly appreciated.
BEST
~
J
Onebase,
First check PSU voltage +15v, -15v and +5V
Best regards,
e-licktronic
Thanks for swift response. I am getting all the correct voltages off the psu. :*(
Re: I goofed. Please help
Posted: Feb 10th, '17, 11:28
by e-licktronic
onebase,
Is your sequencer running ?
is there a burned 100ohm resistor on the PSU bus ?
Best regards,
e-licktronic
Re: I goofed. Please help
Posted: Feb 11th, '17, 04:05
by onebase
e-licktronic wrote:onebase,
Is your sequencer running ?
is there a burned 100ohm resistor on the PSU bus ?
Best regards,
e-licktronic
no lights come on at all. I dont' see any burt resistors... Unless I'm missing it. Which R# is that one?
Re: I goofed. Please help
Posted: Feb 11th, '17, 08:03
by e-licktronic
onebase wrote:e-licktronic wrote:onebase,
Is your sequencer running ?
is there a burned 100ohm resistor on the PSU bus ?
Best regards,
e-licktronic
no lights come on at all. I dont' see any burt resistors... Unless I'm missing it. Which R# is that one?
Those are the 100 ohm resistors on the top edge side of the main board.
Is there leds that light up when power on your Yocto ?
What sequencer mods is selected?
Best regards,
e-licktronic
Re: I goofed. Please help
Posted: Feb 13th, '17, 07:21
by onebase
e-licktronic wrote:onebase wrote:e-licktronic wrote:onebase,
Is your sequencer running ?
is there a burned 100ohm resistor on the PSU bus ?
Best regards,
e-licktronic
no lights come on at all. I dont' see any burt resistors... Unless I'm missing it. Which R# is that one?
Those are the 100 ohm resistors on the top edge side of the main board.
Is there leds that light up when power on your Yocto ?
What sequencer mods is selected?
Best regards,
e-licktronic
ok the lights came on and it mostly work though the kick and clap are triggering every step of the sequence. when i edit the kick or clap sequence I get a more pronounced hit of the instrument. Turning the volume up has the clap bleeding noise.
Re: I goofed. Please help
Posted: Mar 1st, '17, 17:58
by onebase
Question does this issue sound like a busted sequencing chip?