Search found 68 matches
- Jun 4th, '16, 08:19
- Forum: Nava Hardware
- Topic: Accidentaly cut two traces..
- Replies: 3
- Views: 4147
Re: Accidentaly cut two traces..
It would be nice if Elicktronic could provide pdf's of the traces on top and bottom of the board. Would make troubleshooting a little easier.
- Jun 3rd, '16, 18:51
- Forum: Nava Hardware
- Topic: Accidentaly cut two traces..
- Replies: 3
- Views: 4147
Accidentaly cut two traces..
:o Yes, I think I fucked up a little - slipped with my pliers and rammed them straigth down into the PCB. Loooking at the schematics there should be 4 traces that connect IC114 and IC111, right? Are these the connected pads for the IC's (marked as red lines in th image)? Also marked is my fuck-up :|...
- Jun 3rd, '16, 05:12
- Forum: Nava Mods
- Topic: Component numbering
- Replies: 1
- Views: 5749
Component numbering
Is there a component numberings correlation of the passive and IC components, between the Nava and the original 909?
Are the numbering the same?
I was thinking of adding the pitch-mod for my hi-hats, which seems quite doable as long as you can id the components
Are the numbering the same?
I was thinking of adding the pitch-mod for my hi-hats, which seems quite doable as long as you can id the components
- May 31st, '16, 16:27
- Forum: Nava Software
- Topic: sample accents bug RESOLVED (fixed in v1.018)
- Replies: 8
- Views: 7494
Re: sample accents bug RESOLVED (fixed in v1.018)
Is it possible to update the firmware using sysex and midi?
- May 30th, '16, 19:25
- Forum: Nava Hardware
- Topic: post your completed build pics
- Replies: 29
- Views: 24160
Re: post your completed build pics
Nice work!Rowan wrote:Build finished! It all went pretty smoothly a part from 1 faulty 74HC165.
Now you just need to provide us not-quite-finished-yets with some nice demos of it.
Jus so we'll speed up our game
- May 30th, '16, 13:20
- Forum: Nava Software
- Topic: Nava v1.0 Firmware
- Replies: 117
- Views: 174897
Re: Nava v1.0 Firmware
I really hope that the build instructions will be updated with info on how to update the firmware.
- May 29th, '16, 07:07
- Forum: Nava Hardware
- Topic: Mix Out Noisy/Distorted
- Replies: 59
- Views: 114494
Re: Mix Out Noisy/Distorted
hmmm it is something else. but has to do with the muting circuit. I cut the traces to place take the signal after d195, but the mix out is still distorted. :( for now I will remove the 22k resistors again to get a clean mix out. maybe the designer of the kit may find the time to fix this hardware b...
- May 25th, '16, 12:36
- Forum: Nava Hardware
- Topic: My build log - missing parts, questions and suggestions
- Replies: 65
- Views: 48250
Re: My build log - missing parts, questions and suggestions
Daaaang! I found the problem! The right 'standoff' from VR14 is placed directly above a via carrying the signal from R12A to the 4069 VCC pin (14). Since the standoff is connected to GND and touches the untented via when the pot is fully inserted, it shorts the output of the opamp down to GND, elim...
- May 24th, '16, 08:08
- Forum: Nava Mods
- Topic: Secondary Noise Source Kit
- Replies: 70
- Views: 129164
Re: Secondary Noise Source Kit
I'd like 1 package of PCB and chips. And I think a switch would be wonderful
- May 23rd, '16, 15:39
- Forum: Nava Hardware
- Topic: My build log - missing parts, questions and suggestions
- Replies: 65
- Views: 48250
Re: My build log - missing parts, questions and suggestions
i did start listing the missing parts in my build but alas i gave up, also worth noting there are little to no metal film caps in the bom (instead it uses poly box). You should really use those nice Nichicon metal film if you want it closer to the original machine ;) (i was lucky to have a good sta...