Plausible bugs:
I tried to use Yocto to trigger two drum eurorack modules, the results as follows:
1) In Midi mode, the Trig2 (T2) cannot play back any recorded nodes. T1 has no problem.
2) In Edit mode or Play mode, both T1, T2 work fine, no problem.
Search found 31 matches
- Nov 29th, '16, 17:17
- Forum: Yocto v1.0 Software
- Topic: Official Yocto BUGS list
- Replies: 40
- Views: 121728
- Nov 22nd, '16, 10:40
- Forum: Nava Software
- Topic: Nava v1.0 Firmware
- Replies: 117
- Views: 263687
Re: Nava v1.0 Firmware
Hey guys, I can't seem to update the firmware. I can't use MIDIOX because i'm on a mac, so I used SysExLibrarian. The Nava patiently waits while the firmware is uploading, but the trigger buttons don't light up to show the progress. I can see my MIDI interface (UM-2G) is sending MIDI because the LE...
- Nov 20th, '16, 11:32
- Forum: Nava Hardware
- Topic: Gate Triggers don't properly trigger...
- Replies: 13
- Views: 14402
Re: Gate Triggers don't properly trigger...
I was using a multimeter to test it at first. It seems that the multimeter cannot catch the 2ms pulse. So it reads 0.07v all the time. And that makes me think that my circuit is going wrong. Fortunately, Bastien asked me to use a scope to track it. So here are the results. Hope that the next softwar...
- Nov 20th, '16, 09:45
- Forum: Nava Hardware
- Topic: Gate Triggers don't properly trigger...
- Replies: 13
- Views: 14402
Re: Gate Triggers don't properly trigger...
This is the output of Trig-1 of Nava. http://i68.tinypic.com/jruwyr.png It seems to be alright, with 5V peak and at an interval of 124ms which is 120bpm, pulse width 2ms. This is the output of clock Out of Drumbrute. http://i67.tinypic.com/rk4ydw.png With a lower peak of 3.75V and also at 124ms inte...
- Nov 15th, '16, 16:25
- Forum: Nava Hardware
- Topic: Gate Triggers don't properly trigger...
- Replies: 13
- Views: 14402
Re: Gate Triggers don't properly trigger...
Hi Bastien, I have trace through the path. Here is what I found: 1) pin 38 of the Atmega (IC119) is giving 4.80v. *** But I don't see any significant drop of voltage to 0v on triggers 2) pin 3 of J2 connector is giving 4.80v 3) pin 3 of J10 connector on the IO board is giving 4.80v 4) The C leg of 2...
- Nov 14th, '16, 01:37
- Forum: Nava Hardware
- Topic: Gate Triggers don't properly trigger...
- Replies: 13
- Views: 14402
Re: Gate Triggers don't properly trigger...
The 5V S-trig is generated at pin 38 of the Atmega (IC119), but i doubt there would be a problem here, you can check anyway. After that, it goes to pin 3 of J2 connector, be sure to check that the wire isn't broken. Then, the pin 3 of J10 connector on the IO board is connected to a 47k res (R550) w...
- Nov 13th, '16, 17:13
- Forum: Nava Hardware
- Topic: Gate Triggers don't properly trigger...
- Replies: 13
- Views: 14402
Re: Gate Triggers don't properly trigger...
I have the same problem too. I cannot trigger the clock of SH-101. I have a very low Trig-1 output voltage which is way below 2.5v, I have 0.07v only. Which part of the Nava should I check to see if there is a problem?
- Nov 13th, '16, 12:16
- Forum: Nava Software
- Topic: Is this a Bug? Closed Hihat accent cannot be saved
- Replies: 4
- Views: 8045
Re: Is this a Bug? Closed Hihat accent cannot be saved
Thanks Phil for spending your time to try this out.
I guess this must be the software problem? Maybe I should put this in the Bug list.
I guess this must be the software problem? Maybe I should put this in the Bug list.
- Nov 12th, '16, 09:03
- Forum: Nava Hardware
- Topic: Chia Shin Knobs [Small Knobs are SOLD OUT] plz read
- Replies: 204
- Views: 168441
Re: Chia Shin Knobs [IN STOCK]
Just received mine today. They look fantastic. 
- Nov 11th, '16, 11:22
- Forum: Nava Software
- Topic: Is this a Bug? Closed Hihat accent cannot be saved
- Replies: 4
- Views: 8045
Re: Is this a Bug? Closed Hihat accent cannot saved
No one has this problem? So this must be something wrong with my built?
Anyone has any idea which part of my built goes wrong?
Anyone has any idea which part of my built goes wrong?