Search found 17 matches
- Jul 7th, '18, 07:40
- Forum: Yocto v1.0 Hardware
- Topic: Sequencer issue
- Replies: 2
- Views: 5264
Re: Sequencer issue
Opened it up and I'm now getting 3.7v on the 5v lines coming off the power board and I believe it's the 5v that runs the sequencer. It appears as though the headsink slipped down on the regulator and bridged the 3 prongs causing a short. Going to rebuild the power section and go from there. Just a ...
- Dec 1st, '15, 23:07
- Forum: Yocto v1.0 Hardware
- Topic: Any Spare Overlays for Sale
- Replies: 2
- Views: 2749
Re: Any Spare Overlays for Sale
I have one i could sell, $10 plus shipping? I am in Canada
- Dec 13th, '14, 23:50
- Forum: Yocto v1.0 Hardware
- Topic: R208 and R209 burning up!
- Replies: 3
- Views: 3487
Re: R208 and R209 burning up!
Op amp was fine. Nothing else damaged.
- Nov 24th, '14, 22:14
- Forum: Yocto v1.0 Hardware
- Topic: Front Panel Express enclosure.
- Replies: 3
- Views: 3651
Re: Front Panel Express enclosure.
I never used their software before so it's a bit difficult to check all the alignments, but all the cutouts look correct. If you copied everything straight from the ai file from e-lick, all dimensions should be correct too, the only thing you need to make sure of is that the holes on the IO plate a...
- Nov 24th, '14, 21:57
- Forum: Yocto v1.0 Hardware
- Topic: Front Panel Express enclosure.
- Replies: 3
- Views: 3651
Re: Front Panel Express enclosure.
Yes, that is to accommodate the side profiles.
I will have to double check allignment of the back plate holes to make sure there is no stress on the ribbon cable.
I will have to double check allignment of the back plate holes to make sure there is no stress on the ribbon cable.
- Nov 23rd, '14, 22:10
- Forum: Yocto v1.0 Hardware
- Topic: Exploring other enclosure options.
- Replies: 433
- Views: 400319
Re: Exploring other enclosure options.
If he is not up for doing another enclosure run, i've been looking at other feasible options. I used the layout files on the forums here to mock up a full enclosure using Front Panel Express.(minus a bottom cover as i can have that made locally for much less. Just needs to be a 1.5mm piece of metal ...
- Nov 22nd, '14, 07:32
- Forum: Yocto v1.0 Hardware
- Topic: Front Panel Express enclosure.
- Replies: 3
- Views: 3651
Front Panel Express enclosure.
I used the layout files on the forums here to mock up a full enclosure(minus a bottom cover as i can have that made locally for much less). these are the files I've come up with. If someone could look over them to see if they think anything is wrong, i would appreciate the feedback as this is the fi...
- Oct 6th, '14, 02:54
- Forum: Yocto v1.0 Hardware
- Topic: Exploring other enclosure options.
- Replies: 433
- Views: 400319
Re: Exploring other enclosure options.
Ill take one as well.
- Jul 4th, '14, 05:35
- Forum: Yocto v1.0 Hardware
- Topic: Noise section trimmer voltage?
- Replies: 81
- Views: 65701
Re: Noise section trimmer voltage?
seems like i had a bad q35. I replaced it with another NPN with the same ECB pinout and now i get between 200-750mV. I'm going to play with R127 now to see if i can get it to 130mV.
- Jul 4th, '14, 04:57
- Forum: Yocto v1.0 Hardware
- Topic: Noise section trimmer voltage?
- Replies: 81
- Views: 65701
Re: Noise section trimmer voltage?
What are some of your guys voltages on pin 2 and 3 of the opamp?