I built the Yocto2 and Nava - but I hate how flimsy the wain volume pot's are on both of them - has anyone sourced alternative parts that fit but feel as solid as the other pots?
Thanks!
Search found 16 matches
- Apr 9th, '18, 03:07
- Forum: Nava Hardware
- Topic: Better main Volume pot?
- Replies: 1
- Views: 3173
- Mar 7th, '18, 01:55
- Forum: Nava Hardware
- Topic: No rimshot and low handclap
- Replies: 6
- Views: 4691
Re: No rimshot and low handclap
I've tracked the rimshot problem down to a bad 5218. One of the pins was broken but it's also just dead now it seems.
- Mar 5th, '18, 21:38
- Forum: Nava Hardware
- Topic: No rimshot and low handclap
- Replies: 6
- Views: 4691
Re: No rimshot and low handclap
I did have a spare, just one! I must have pulled it from an old Roland board at some point because it's "vintage". I removed the chip that came with the kit and the sound didn't change. I put in the spare I had and adjusted the trimmer, and it sounds AMAZING now. I appreciate the offer, bu...
- Mar 5th, '18, 19:01
- Forum: Nava Hardware
- Topic: No rimshot and low handclap
- Replies: 6
- Views: 4691
Re: No rimshot and low handclap
Thank you, I just saw the other threads referencing that IC.
I've got:
AN6912
M.609
Nothing on the bottom.
I might have a spare in stock, so I'll give it a try.
On the rimshot I think my problem is at Q65, or near it. I'm hoping I can just pull that and see if it works in a tester.
I've got:
AN6912
M.609
Nothing on the bottom.
I might have a spare in stock, so I'll give it a try.
On the rimshot I think my problem is at Q65, or near it. I'm hoping I can just pull that and see if it works in a tester.
- Mar 4th, '18, 09:51
- Forum: Nava Hardware
- Topic: No rimshot and low handclap
- Replies: 6
- Views: 4691
Re: No rimshot and low handclap
An update: I have a signal on F1, F2, F3 and TRIG. No signal on ENV or ACC. No signal on IC50, but it is getting power. I did have a short in the Hi Tom area originally, but that voice seems to be okay. I didn't see any magic smoke but I did smell some smoke, could have been my imagination. There ar...
- Mar 4th, '18, 02:05
- Forum: Nava Hardware
- Topic: No rimshot and low handclap
- Replies: 6
- Views: 4691
No rimshot and low handclap
Working on finishing up a Nava. I've got no rimshot sound and the handclap seems like it's low and maybe a bit more muffled than it should be.
Any tips on what I can test?
Any tips on what I can test?
- Feb 26th, '18, 06:08
- Forum: Nava Hardware
- Topic: Solved - Need help with a -15 and GND short
- Replies: 1
- Views: 2169
Re: Need help with a -15 and GND short
Short mystery. I pulled all the 0 ohm resistors until I got to the low tom section and the short disappeared. At that point it was easy to trace the issue to a bad solder joint.
Now onto figuring out what I fried.
Now onto figuring out what I fried.
- Feb 26th, '18, 02:29
- Forum: Nava Hardware
- Topic: Solved - Need help with a -15 and GND short
- Replies: 1
- Views: 2169
Solved - Need help with a -15 and GND short
I'm getting close to finishing up a Nava build. I shouldn't have been so confident in doing the initial testing - I smelled some smoke and heard a buzzing sound coming from the main board. There were a few IC's I had oriented wrong in the crash section, so I pulled those out. They weren't hot or bur...
- Dec 31st, '17, 04:05
- Forum: Yocto² Hardware
- Topic: Yocto² Mouser BOM Official Thread
- Replies: 26
- Views: 38615
Re: Yocto² Mouser BOM Official Thread
is CD4049UBE a suitable replacement for CD4049UBEE4? Mouser has it in stock, and I can't quite tell the difference between the part numbers from the datasheet. I have 11 of them here, tried 3 of them and I've had trouble with some of the instruments triggering. So either they aren't a good replaceme...
- Dec 19th, '17, 17:26
- Forum: Yocto² Hardware
- Topic: Noise problem
- Replies: 14
- Views: 17553
Re: Noise problem
I had the same problem, a 100k trimmer for TM4 got me to 130mV RMS. Now just a potentially faulty IC3 causing intermittent clap failure is my only remaining problem.