Hi there.
My Nava has been running flawless for some years now. But mid tom is starting to have a ultra short decay when I move the Tune knob above position 4. From position on 1-4 on the Tune knob it works like normal. Any ideas?
Cheers
Mikkel
Search found 12 matches
- May 30th, '19, 14:43
- Forum: Nava Hardware
- Topic: Mid tom, short decay
- Replies: 0
- Views: 27265
- May 31st, '17, 19:26
- Forum: Nava Software
- Topic: Official Nava BUGS list
- Replies: 72
- Views: 103598
Re: Official Nava BUGS list
+1 For updating the code on github.
- Apr 24th, '17, 19:56
- Forum: Nava Hardware
- Topic: Hi Tom volume - Firmware or hardware?
- Replies: 3
- Views: 3311
Re: Hi Tom volume - Firmware or hardware?
Thank you.
So a pull down resistor on every accent out.
Will try it soon.
Cheers
Mikkel
So a pull down resistor on every accent out.
Will try it soon.
Cheers
Mikkel
- Apr 15th, '17, 15:00
- Forum: Nava Hardware
- Topic: Hi Tom volume - Firmware or hardware?
- Replies: 3
- Views: 3311
Hi Tom volume - Firmware or hardware?
Hi there. I have a quite high Hi tom volume, with only a little difference between accented note and just a normal trigger. I can see that I have much more power on the accent pin on IC114 compared to Mid and Low tom. IC114 Pin1: 1.9V no accent Pin1: 2.9V Accent Pin12 and 13: 1V no accent Pin12 and ...
- Apr 15th, '17, 14:35
- Forum: Nava Hardware
- Topic: Everything works, except snare.
- Replies: 1
- Views: 2456
Re: Everything works, except snare.
Does anybody know if im on the right track, before I start desoldering and properly destroy an 5218?
Cheers
Cheers
- Apr 11th, '17, 16:55
- Forum: Nava Hardware
- Topic: Everything works, except snare.
- Replies: 1
- Views: 2456
Everything works, except snare.
Okay 9 months of soldering is over, and my NAVA is working... Nearly. My snare is really low, but as for the small amount which comes out, the level pot is working reverse. All the tone controls works as intended. Any suggestions? Except for one part of IC40 being dead? I have checked all connection...
- Apr 11th, '17, 16:45
- Forum: Nava Hardware
- Topic: -5v at J2 and Nava wont boot.
- Replies: 4
- Views: 4190
Re: -5v at J2 and Nava wont boot.
Missed that it got fed by J2 and I needed to do all the crimping before I could test it.
Everything works now, except the snare.
Everything works now, except the snare.
- Apr 10th, '17, 16:04
- Forum: Nava Hardware
- Topic: -5v at J2 and Nava wont boot.
- Replies: 4
- Views: 4190
Re: -5v at J2 and Nava wont boot.
Ok stupid socket at IC118 at leg 1, that fixed the negative current. Now I have 0V at the sequencer section instead of +5V in the sequencer section. I have +5V at the 'instruments' Any suggestions? of where to look?
- Apr 10th, '17, 15:39
- Forum: Nava Hardware
- Topic: -5v at J2 and Nava wont boot.
- Replies: 4
- Views: 4190
Re: -5v at J2 and Nava wont boot.
I got the right +5V at the Ride, Crash and Hihat roms, but I have -8V at TP1 and it doesnt react when I turn TM2.
- Apr 10th, '17, 09:27
- Forum: Nava Hardware
- Topic: -5v at J2 and Nava wont boot.
- Replies: 4
- Views: 4190
-5v at J2 and Nava wont boot.
Hi there.
I measure -5v at the sequencer (j2), but the connections to the mainboard is right, and I measure +5v there, when everything is connected.
+15 and -15 is all-right.
What have i done wrong.
Cheers Mikkel
I measure -5v at the sequencer (j2), but the connections to the mainboard is right, and I measure +5v there, when everything is connected.
+15 and -15 is all-right.
What have i done wrong.
Cheers Mikkel